proton:raspi_setup
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
proton:raspi_setup [2016/06/18 07:36] – seth | proton:raspi_setup [2016/06/19 13:07] – seth | ||
---|---|---|---|
Line 1: | Line 1: | ||
** Experimental and for linux pros only ** | ** Experimental and for linux pros only ** | ||
- | These steps are what I use to compile stuff by copying things from my Windows computer. | + | Here is how to setup the Raspberry Pi to support |
- | Steps: | + | From my tests I got it working two ways: |
+ | |||
+ | 1. Set it up using the OpenGL experimental driver. | ||
+ | |||
+ | 2. Set it up using GL ES, won't work in X11, works full screen by starting from console. | ||
+ | |||
+ | |||
+ | ** Instructions to setup GLES with Raspberry Pi and run Proton SDK examples ** | ||
+ | |||
+ | |||
+ | These steps are what I use to compile stuff by copying things from my Windows computer. | ||
+ | |||
+ | * Give the video card more memory on the pi. Run raspi-config and give it at least 128 or so to be safe. | ||
+ | * Install cmake on the pi (sudo apt-get install cmake) | ||
+ | * Do "sudo rpi-update" | ||
+ | * Run the following from a shell: | ||
+ | |||
+ | < | ||
+ | sudo apt-get -y install xcompmgr libgl1-mesa-dri && sudo apt-get -y install libalut0 libalut-dev && sudo apt-get -y install mesa-utils | ||
+ | |||
+ | sudo apt-get install libglu1-mesa-dev freeglut3-dev mesa-common-dev libgles2-mesa-dev libgegl-dev | ||
+ | </ | ||
+ | |||
+ | * Do the following from a shell window to install SDL2 from source: | ||
+ | |||
+ | < | ||
+ | cd ~ | ||
+ | wget https:// | ||
+ | tar zxvf SDL2-2.0.4.tar.gz | ||
+ | cd SDL2-2.0.4 && mkdir build && cd build | ||
+ | ../ | ||
+ | make -j 5 | ||
+ | sudo make install | ||
+ | </ | ||
+ | |||
+ | * To test, type " | ||
+ | |||
+ | |||
+ | Step 2: Proton stuff | ||
* Install linux tools for Windows, rsync and ssh should work from the command line | * Install linux tools for Windows, rsync and ssh should work from the command line | ||
* Setup a ssh key pair so you don't have to type passwords | * Setup a ssh key pair so you don't have to type passwords | ||
* Edit SetupVars.bat and edit the IP to the pi | * Edit SetupVars.bat and edit the IP to the pi | ||
- | * Install cmake on the pi (sudo apt-get install cmake) | ||
- | * Install SDL2 on the pi (sudo apt-get install libsdl2-dev libsdl2-image-dev libsdl2-ttf-dev libsdl2-mixer-dev) | ||
* Run CopyStuffToPi.bat. | * Run CopyStuffToPi.bat. | ||
+ | * Edit the RTBareBones/ | ||
* RTBareBones/ | * RTBareBones/ | ||
+ | The last step of the build copies the rtbarebones binary to / | ||
+ | |||
+ | RTSimpleApp is much the same, although you'll need SDL2's mixer as well. Unlike with the base SDL2, we can just grab a pre-compiled one like this: | ||
+ | < | ||
+ | sudo apt-get libsdl2-mixer-dev | ||
+ | </ | ||
+ | And that should compile ok. We don't have a mouse or anything but I can see it's running at 60 fps... | ||
- | If you look at the RTBarebones/ |
proton/raspi_setup.txt · Last modified: 2023/12/03 06:42 by seth